Accord Fogs with Type-S Grills by guitarplayer16

By diyauto
( 2 )

20 minute read

Accord Fogs with Type-S Grills 


Compliments of guitarplayer16 @ https://acurazine.com


4-29-2011


Click Here to check out NSXCessive's wiring and mounting DIY for EVEN MORE Accord Foglight information - the more the merrier, right? =)

Hey guys,

A few weeks ago, I posted a teaser picture of parts I purchased, and some people thought it couldn't be done.

I present you... the DIY to Accord Fogs with the Type-S grills.

Just letting you know in advance, that for this mod, I can not tell you exactly where to cut, measurements, etc, since this is a retrofit.

Everyone's results turn out different.

Materials:

+ Dremel (with cutting bit and sanding bit)
+ Drill (and drill bits)
+ Various Screws and screwdrivers that you probably have in your garage.
+ Safety Goggles (you DO NOT want pieces of plastic in your eyes)

Getting the Parts:

Okay, so here is what you have to buy:

Type-S Lower Grills: 71107-SEP-A20ZA, 71102-SEP-A20ZA
Type-S Chrome Bars (for the lower grill): 71126-SEP-A20ZA, 71121-SEP-A20ZA
Center Grill: 71120-SEP-A10ZA

Alternately, you can get the base 07/08 lower grill bars if you want it to match your silver (non-chrome) upper grill.

Get those 5 parts ordered, and order some Accord fogs too.

In my install, I used OEM 03-05 Accord Sedan Fogs.



Okay so now that we have all our parts, we're ready to start working!

Disclaimer:

This modification requires you to cut your grills, fogs, and bumpers. If you mess up, I will not be held liable.



For this mod, you have to remove your front bumper.

Check out this cool video showing you how:




Step 1: Remove your old grill

There should be a lot of screws that hold the grill in. Remove them with a Philips Screwdriver and place them aside.



Comparison between the two grills:



Step 2: Cut your new Type-S grill in half

The Type-S grill is a little tall, so we'll be removing some of the middle section which is behind the bar, so nobody can see your cuts.

You can see where I cut it in half, using the labels as reference:

I suggest you cut higher than where I cut, because I found out I cut a little too close to where the cuts would be visible lol




Step 3: Cut out this little mounting nub.



Step 4: Mount this upper half onto the bumper

Using the stock mounting points, you can screw in a few screws to mount the top half.

Step 5: Mounting the bottom half

Okay, for this bottom half to fit, you have to make new holes at the bottom of the grill so it would fit with the two little sticks that point out from the bumper.

Just grab your drill and a drill bit that's the same size as the things that stick out of the bumper, and drill away.
Make sure you DO NOT drill into places where you don't want to drill, so watch the angle that you drill at or you might go through the other side.



Final product after cutting/trimming:




Step 6: Mounting everything onto the bumper for good

Okay, so I'll tell you the exact steps for what I did to finalize everything.

Don't worry if the grill doesn't look like it fits right, because the curvature is different, but it will look good when the bumper is back on the car.

The top half got mounted using 4 screws (blue)
The bottom half got mounted using a custom bracket I used made out of plastic, so always save the plastic you make with your cuts. I then drilled two holes in the piece of plastic bracket. Then I used the mounting screws and screwed everything in. So yeah, all you have to do is find a piece of plastic and drill 2 holes in it to make a custom bracket lol (red)
Then lastly, I JB-Welded the top half to the bottom half. (green)

Legend: 
Blue: OEM screws from old grill (6)
Green: JB Weld
Red: Plastic bracket made from plastic scrap lol
Yellow: This section of the bottom half pushes in perfectly with the opening of the top half.



That's it!

The center grill is done and mounted!



If you spot any light around the edge your grill, just remember it's okay and when the bumper is on the car, you won't see it.



Here comes the Accord DIY.
The hardest part.

I made my fogs point inwards as much as possible so everything is flush with the bumper and doesn't glare oncoming traffic.

This was inspired by AckTL05's installs.

Just a warning: the install will take a long time, with this DIY or not.

You have to cut behind the bumper, the fog lights, and the (brand new) lower grills.

You can DO IT. It will take a long time.

My install spanned me a whole week, which days I spent 6 hours doing nothing, trying to figure how to make the fogs fit.

Also, my fogs were trimmed for my A-Spec front lip, so if you don't have one, you can't really follow my instructions too detailed LOL

Step 1: Un-Attach A-Spec Lip

If you have an A-Spec lip, don't fully remove it; just un-attach the side, and have the lip still mounted from the middle screws.

Step 2: Remove the lower grill

There are 6 tabs, 3 on top, 3 on bottom. Make sure you don't scratch your lip kit if you have one.

Step 3: Cutting the Area Behind the Fogs

Cut the area behind the fogs so they can fit in.

This is the first cut I did:



I was then told the cut was too small and I had to widen it.

Step 4: Trimming the fogs


Okay, this step is the hardest because it requires you to trim, then test fit.
Then you do that about 100 times again until it fits nicely.

You want your A-Spec lip in position while trimming the fogs.

DO NOT GIVE UP DURING THIS STAGE!

I was actually about to give up, but then everyone convinced me that all I have to do is keep trimming it down mm by mm.

When I tried placing it in:



You'll notice the fogs have a weird curve to it, so we're gonna try to level things out.

First thing I trim is the plastic on top of the tabs.



Then I trim the inner-top.



Then I trimmed the upper outside edge.

Be careful when you're trimming and take your time.
I went a little fast and the bit caught the edge and dragged it down on the accord fog housing. It also caught my A-Spec lip and made an inch mark in it DAMN ME!!!!

Really hardly noticeable though, so if you do happen to screw up, let it slide lol.



Then I trimmed along the whole bottom to make everything fit with the A-Spec lip. Didn't trim too much though, just a few mm's.

Then I had to make a notch on the outside edge to fit with the A-Spec lip.




Make sure everything is just flush with the bumper.

How much did I end up cutting behind the fog area?




Step 5: Mounting the Fogs

You can really mount them any creative way you want.

I decided since the foglights were already really jammed in the opening, I only need one screw into the bumper.

So what I did was I dremeled (with sanding bit) a small hole big enough to fit the screw on the outmost side behind the bumper, found a long screw that fit with the screw hole on the fogs, and used a BIG washer. Did the same for the other side.

Make sure everything is flush and nice how you want it.

Here's a picture:




Make sure those are tight, and screw in the other side, with the screw that came with the fogs, and screw in the screw that's directly behind the fogs (that are hooked to the silver bracket).

So yeah, I only used 3 screws for each fogs to mount them LOL

They're not going anywhere either.

You can use the tabs and a really long screw too, but I felt that my fogs were already jammed tight so no need; plus my Type-S grill is holding them really tight.

Step 6: Cutting the Type-S grill

Start by cutting the fog light section of the grill.

Stupid me didn't take any pictures of the cutting.

Then put the grill against the bumper, and mark off where you need to cut so it would fit in with the Accord fogs.

You can really eye-ball where to cut.





Step 7: Mounting the Type-S Lower Grills

To mount them, you have to widen the mounting holes.
I only widened the 2 (top and bottom) inner mounting holes. I made the holes wider and closer to the other holes.

Use a dremel (sanding bit) to widen them.

Then you partially remove the A-Spec lip and slip them in.

This step might take a few tries and trims.

The cool thing about when I put my lower grills in, and then I pushed the A-Spec lip in, it caught my Accord fogs and made them perfectly flush with the bumper lol.

Step 8: Mount the chrome bars


We're almost done!

Take your chrome bar, then line it up with the mounting holes at the bottom and push in until the mounting clips click in. I then found out that the mounting holes had some "play" left and right, so I pushed the chrome bar as close inwards as it will go.

All done!

Everything should look flush.






Materials:

Screwdrivers, electric tape, wire (16 gauge is what I used), ring terminal, butt-connectors, T-Tap or Splice connectors, in-line fuse.

This is how you wire the fogs up so they come on when your parking lights turn on. I DO NOT recommend you do this if you plan on using an HID kit for your fogs.

We will be starting the wiring from the inside.

Step 1: Remove the driver's lower dash panels

All I had to do was remove a screw on the right most side, and just a lot of force to take out the driver lower dash panel.

The bottom panel will fall out too.

Unplug all connectors

Step 2: Remove the dummy switch


We have to remove the dummy switch in order to put in our new foglight switch.

All you have to do is pinch in the top and bottom and push it out to remove the dummy switch.

Step 3: Place in the foglight switch

Now since the dummy switch is out, we now place our foglight switch in.

All you do is push the switch in from the outside.

Step 4: Plug in the blue skinny connector to the switch

Pretty simple,. Take your switch harness and find the skinny blue connector. Just push it in until it clicks.



Step 5: Ground the switch

There will be a black wire with a ring terminal at the end. All you have to do is bolt the terminal onto a ground point. The point I used was directly under the steering wheel.




Step 6: Run a long wire through the firewall

For this, you're going to have to use your brand new roll of 16 gauge wire.

From inside the car, look to the left under the driver's dash. You should see a big bunch of wires coming from one big hole in the firewall.

What I did, was just taped wire to the end of a coat hanger, and POKED using little force, through the rubber. Then you grab the wire through the engine bay. Remove the plastic covers in the engine bay of course.



Step 7: Hook that new wire up!

Now, that the hard part is over, cut the wire to a good size that will reach your relay. Then inside your car, connect the "new wire" to the green wire on the switch harness.

You'll have to remove some plastic from the harness to connect the wires.



Last step inside the car: Tapping into the parking lights.

See the solid blue wire on your switch harness?

Yeah, that wire taps into the parking light wire.

The parking light wire is the top left wire that is red and black.

I used splice connectors, so it was difficult.



All done inside the car!!!!

Now onto the engine bay.

Step 1: Bolt down the relay.


Your kit came with two relays. One black and one gray.

Use the black one only, and put the gray one away haha

You want to bolt down your relay somewhere.

I bolted mine beside the battery using the engine air filter box.



Step 2: Connect the harness to the relay.

Next, take the brown connector from your fog harness, and plug it in the relay.

Step 3: Getting the POWAH!!

On your fog harness, there should be a red and blue wire.
Clip off the end, and connect it to an in-line fuse holder.



Then at the end of your in-line fuse holder, add a ring terminal to it.

Then open the fuse box, and unscrew the bolt farthest from the front.

Put the terminal in, then bolt her down.



Step 4: Connect the wire that we ran though the firewall

So you still have that "new wire" hanging around.

Now we're going to connect that new wire, to the green wire on the brown skinny connector.



Step 5: Grounding

In-between the two fog connectors, there are two black ground wires with a ring terminal. Cut off the ring terminal (with an inch of wire still on it so you can splice later!). Then place this aside.

Then take your roll of new wire your bought and cut two 3' long wires. What we're doing is extending the ground wires.

Then you're going to connect the new wires to the ground wires.



Then at the other end of these new wires, connect the ring terminal (with the inch of wire so that we can splice) that we cut off earlier.

Then bolt this ring terminal to the body ground. I used the same ground as the battery.



Last Step: Connect the fogs.

Well, this one should be the easiest.

All you do is take the fog connector, and push it into the bulb until it clicks.

YAY! All done!

It wasn't so hard, was it?

Now, I'm telling you right now; how you organize or place your wires are all up to you. I'm probably going to clean my wiring up myself, when I have time. I'm just glad mine light up LOL

Special thanks to omnuts and rockstar143 who helped me throughout the whole process.







If you have any questions, just let me know and I'll do my best to answer it.

I'd like to thank DeathMetal, jwr0ng626, Mem04TL, rockstar143, omnuts, Roger555, AckTL05, el.profe for helping me with this mod, which in turn helps me make this DIY for you guys to use.

Cheers!



Comments