1dirtyZ's Conversion by 1dirtyZ

8 minute(s) of a 153 minute read

the intercooler is firmly affixed to the car , i hacked up the bumper some more to clear the intercooler . off course i forgot to bring the camera, so i'll have to snap pics tomorow. 

i'm planning on relocating the cooler tomorow , as well as begin plumbing the intercooler piping ( i can only do 2 u shaped bends from the sides, untill i get the motor in so i know where the rest will fit.

i should have the engine finished by friday evening if all goes well. and if i'm lucky ( which i think not) i might ddrop it in that night 

i also noticed the power steering reservoire hose ( low pressure side) is beginning to weep , so i guess it was the wrong type of hose will be changing that out soon .

8/8/08

well we're back on track again 

here is the intercooler finaly fixed in place :

and the engine is in too:

the tranny cooler has been re located to the opening in the passenger inner fender , it will also have a small cooling fan to assist in cooling.

the tranny is out to be checked and refreshed , and i ordered an SFI flex plate that should be here some time next week.

now that the engine is in , i can start the intercooler plumbing and mount the blower, bov , and drive system as well as cleaning up the engine compartment.

after that ( assuming i get the camro's super pulley and trans shield in next week and i install them ) i 'll take the camaro off the lift and put the stang on it and start the fule system .

planning on sumping the tank, two external pumps and filters, new fuel line to the engine, regulator, and reuse the stock feed line as a return. i'll be using the camaro's old l-92 manifold, 75 lb injectors , and fuel rails .

part of the appeal of this car for me is that it looks sooo nasty and cheap , that you never give it a second look when you see it pass by , think of it as an excersize in "good enough engineering " 

best part is the look on people's faces after you rip them a new one ( especially exotics ) !!!

any how , enough gloating on with the updates :

finally got the fan on the cooler , just need to wire it now:

i also installed the intake, rails , and tb, and mocked up the blower bracket and checked the alignment and shimmed it accordingly:

this is where i found out how big this blower is 

as you can see , i ran out of space

the blower actually touches the core support depending how you clock it . i have two options on how to run the pipes:

the first would be just like i have it on the camaro , pointing towards the passenger side and down:

then making a u turn into the passenger side intercooler inlet, the exiting from the driver side and snaking its way into the inner fender and entering at a 3 or 4 ocklock position ( looking at the front of the car ), which means i can't use thea spot on the inner fender for the meth injection pump and resv. , and i have a feeling that with the pipe in the 3 or 4 oclock position , it would feed the passenger side more air than the driver side ( read on to know what i'm comparing it to)

the second way is to clock the blower like so :

then the outlet would just make a u turn into the driver side intercooler inlet ( the u- bend i have fits perfect- just needs to be trimmed a bit), then from the pass. side intercooler it would make another u turn and shoot stright towards the center of the car , then 90 deg up into the throttle body ( entering from the 6 oclock position ), this way i'm sure both banks will get and equal amount of air, meth , and whatever i'm going to spray up that tube 

in both cases i have to move the radiator forward some more , there is not enough room for the filter and elbow ( note, this is without the radiator inplace ) :

this also means i have to move the intercooler farther out ( well at least the bottom part of it ) so the radiator can clear it .

after mocking up things i was thinking of just hacking up the core support and using some round tube fab me up a new one ( like we did on azooooz's stang), but after clocking the head unit like i mentioned in the second way , it became apparent i can keep the core support and only notch it a bit to make room for some movement .

mr. angle grinder will be busy tomorow

so , if i'm lucky tommorow and get the blower all nice and comfy in its place , i'll start re locating the intercooler and radiator and if i have time , maybe begin the piping process ( i wasn't expecting putting the manifold and bracket on would take so long). i should also clean under the car so i can lay down there while i install the starter and the pass side header.

8/9/08

mr. angle grinder and mrs BFH went to town on the core suport , i now have clearance for the blowerand any movement that might take place . off course i just relized i didn't take a picture of the aftermath 

any how, here is how the blower looks when you remove the radiator (for future refrence):

i managed to relocate the radiator forward inorder to clear the blower , i think i have it a good 3 inches forward now. i just bolted extension peices on the ac condenser tabs on the bottom of the support and bent them upwards to sandwich the radiator between them and the upper rad. hold downs. i can now install my air filter :

off course that meant i had to relocate the intercooler ( again ) to clear the radiator. i was planning on tilting it more by pushing the bottom part out some more, but then i relized that i can lower the intercooler a bit and it would fit real nice in the bumper! 

i guess the first time i set it up i was planning on using the inside bumper ( i still can , i just need to trim it). i also am debating wether i should trim the whole bottom peice of the bumper or not? you can see here how low the intercooler is and how the bottom part is in the way :

here you can see how the intercooler barely shows from under the plastic peice, it used to butt up against it before:

i never got to the "installing the starter and passenger side header " part , and i don't think i'll do it tomorow. most likely , i'll mount the blower, finalize intercooler braces , and clean up the place ; its a mess !

after cleaning it , i'm thinking of fabbing up a patch plate to close the hole i made in the core support to stiffen it a bit , right now its only there for moral support