1968 Volvo project Pure Volvocity by 68EFIvert

5 minute(s) of a 271 minute read

I received my samples in from TechFlex. I ordered some Insultherm and Insultherm Tru-Fit. The product will go on my spark plug wires. I ended up going with the Tru-Fit. It was a little smoother looking and slightly easier to work with. I ordered the 0 gauge which should expand over my wires and have a little extra capacity. The sample I ordered was for 3/8" and was a little loose fitting. The plug wire diameter was .32" so slight smaller than 3/8". I believe they will help protect the plug wires up to 1,200 degrees. I ordered some more shrink wrap to seal up the ends of the wrap and make a clean look.
https://www.techflex.com/high-temper...ltherm-tru-fit

The last couple weeks have all been about wiring, wiring and more wiring. I have most of the basic systems in place now and am connecting the different systems together. There is a lot of CAN connections that I really don't understand so my tuner/chassis guy will help me with the final connections. The engine Harness for the Haltech will need to be shortened quite a bit in order to look tidy in the engine compartment. Some wires are about 2 feet too long.

During part of the wiring I decided to move away from a Taylor Battery disconnect switch in favor for a remote battery disconnect that will provide a little theft deterrent as well. I went with a Cartek piece that is pretty cool. A simple push of a button can disable the entire car but leave some circuits open like an alarm. It is not the most cost efficient piece of equipment but I was how it was working on a Lamborghini last week and was impress with it. So simple to install and effective. https://www.cartekmotorsport.com/battery-isolators/

I hope to have all the wiring done in the next 2-3 weeks. I figure there is still another 40 hours to go there, maybe less if I stop coming up with items to add on. LOL!

I will soon be waiting for the body guy to come over to my house. I will need him to fit the hood and install the hood hinges before I can put in the radiator for the last time. Once the hinges are on the hood can be removed until it is ready to go on for the final time. This car is like a lego kit. This has to be done before this and then on to the next component that must be installed. If one step is missed then you go back to the beginning and start over. Really slows down the final assembly but the final assembly will be super clean.

5-13-2021

A little more progress. Got the brakes bled today and did a little weighing if the car. Still missing the hood and most of the interior but she weighed in at 2922 lbs. I figure when she is fully done it should be around 3100.

I am sure that is more than stock but there is a whole lot more going on than stock. Coming into the home stretch though. My tuner will be ready for the car by late June. I should have everything buttoned up before then. Most of my time lately has been spent wiring and making sure the wiring was clean. Lots of heat sharing and braiding going on. Kind of a pain in the butt but it will be worth it.

7-13-2021

Thanks for the compliments guys. The car ready for the tuner but the tuner isn’t ready for the car. Been taking care of little things like trunk popper and door handles adjustments. I am running out of things to do at this point.

Dynamat at is a good product and Boom Mat is as well. DEI makes Boom Mat and is one of the best manufacturers of insulation and sound deadened products. I have quite a few items from them and they were very helpful when I was looking into them while at SEMA a few years ago. I actually do have a little Dynamat on the car. It was used on the underside of the hood. I don’t think you would go wrong with either product.

My interior guy will put down another layer of sound deadened and then carpet pad. I still need to put a square or two inside the doors. Maybe I will order that tonight. I guess it goes to show you are never quite done with car projects.